PRISULON DCA 130 S
Guar ether(powder)
Universal thickener for textile printing on all kinds of fibres and with all ayestuff classes except reactive dyestuffs and
naphtholates. Well stable to water hardness, bivalent and trivalent metal saltsm, all common printing auxiliaries, burn-out
and discharge chemicals. The colour depth can be increased by adding PRISULON CMS 10(starch ether). Due to the low
viscosity and long-flowing behaviour, the penetration capacity is optimal. PRISULON DCA 90 with a higher viscosity is
more economical but doesn' t penetrate as well.
application amount:12.0-13.0% in stock
60.0=65.0g/§¸ in print paste
pH value in stock:6.5-8.0
ionic character:non-ionic
PRISULON DCA 90
Guar ether(powder)
Universal thickener for textile printing on all kinds of fibres and with all dyestuff classes except reactive dyestuffs and
naphtholates. Well stable to water hardness, bivalent and trivalent metal salts, all common printing auxiliaries, burn-out
and discharge chemicals. The colour depth can be increased by adding PRISULON CMS 10(starch ether).
PRISULON DCA 1200 S with a lower viscostiy penetrates even better.
application amount:8.0-8.5% in stock
40.0-45.0g/§¸ in the print paste
pH value in stock:6.5-8.0
ionic character:non-ionic
PRISULON E 100
Guar derivative(powder)
Thickener for carpet printing, space dyeing and carpet continuous dyeing.
Pourable powder, suitable for automatic injector dissolving systems. Non-flowing, highly pseudo-plastic pastes result
which facilitate the production of frosting-free prints.
application amount:1.5-2.0% in stock
0.5-1.0g/§¸ in the print paste
pH value in stock:6.5-8.0
ionic character:non-ionic
PRISULON E 25 LS
Guar derivative(powder)
Thickener for printing carpets and acrylic plaids, space-dyeing and continuous carpet dyeing. Produces short-flowing,
pseudo-plastic pastes facilitating frosting-free priints. The product is adjusted dustfree and dispersible and can
therefore be excellently applied by hand using dissolving stations with slow stirreses. Swelling is caused by adding
acid(pH<7). The products cannot be used in an alkaline medium(without use of special auxiliaries). PRISULON L 100 S
has a higher viscosity and is more pseudo-plastic.
application amount:2.0-2.5% in stock
0.8-1.2g/§¸ in the print paste
pH value in stock:9.0-11.0(adjust acid for swelling)
PRISULON GT 1000M
Biopolymer(powder)
Thickener based on biopolymer, especially for millitron spray printing. The rheology is adjusted to the spraying
technique. Well penetrated print destigns with sharp outilines and little frost result. The viscosity of the colour pastes is
largely stable to additions of electrolytes and acid.
PRISULON GT 1000 M is very slowly microbially attacked.
However, we recommend a preservation with CHT-PRESERVATIVE TDF to protect the additives from microbial attack.
application amount:1.5-2.0% in stock
pH value in stock:5.5-8.5
ionic character:anionic
PRISULON GTS 800
Starch ether(flakes)
High solids thickener for carpet printing. Produces well penetrated prinis free frosting and with a high colour yield.
application amount:9.0-10.0% in stock
30.0-40.0g/§¸ in the print paste
pH value in stock:9.5-11.5
ionic character:anionic
PRISULON L 100 S
Guar derivative(powder)
Thickener for carpet printing, space-dyeing and continuous carpet dyeing. Produces short-flowing, highly
pseudo-=plastic pastes facilitating frosting-free prints. The product is adjusted dustfree and dispersible and can
therefore be excellently applied by hand using automatic dissolving stations with slow stirrers. Swelling is caused by
adding acid(pH<7). The products cannot be used in an alkaline medium(without use of special auxiliaries). PRISULON E
25 LS is slightly depolymerized, thus penetrating slightly better.
application amount:1.5-2.0% in stock
0.5-1.0g/§¸ in the print paste
pH value in stock:9.0-11.0(adjust acid for swelling)
ionic character:non-ionic
PRISULON PD 300
Polyacrylate, ammonium salt(paste)
Thickener for printing with non-ionically finished disperse dyestuffs. Being easy to dose PRISULON PD 300 is ideal for
afterthickening transfer print pastes. Due to the good dispersibility it can be added to preswollen print pastes.
Please note that the complete product is stirred and homogenizen. The product is completely viscous after stirring for
5-10min. We recommend PRISULON SNP 113 S as base thickener for transfer printing. The rheology can be highly
modified by combining ith with PRISULON PD 300.
application amount:1.0-25.0g/§¸ in the print paste
pH value(2% sol):8.0-9.0
ionic character:anionic
PRISULON R 5
Guar derivative(powder)
Thickener for Africa print with fast bases and fast salts, phthalogen and monofunctional reactive dyesuffs. Also
applicable as additive for vat 2-phase printing(coagulates with borax).
application amount:4.5-5.0 in stock
20.0-25.0g/§¸ in the print paste
pH value in stock:9.0-11.5
ionic character:non-ionic
ĦĦ